Erbauer Zapfenschneider und Kegelsenker-Set 4-tlg Artikelnummer: 3375T

11,99 €
3 in 1- Set. Einsatzbohrer, Spitzsenke und Zapfsenker in einem Bohrer vereint. Enthält die gängigsten Größen (9,5 und 12,7 mm).
-
Technische Daten
-
Zusätzliche Information
Artikelbezeichnung
3375T
Lieferumfang
2 x Zapfenschneider (9.5 und 12.7 mm), 2 x Kegelenker (9.5 und 12.7 mm) und Sechskantschlüssel
11,99 € Inkl. 19% MwSt., (zzgl. 4,95 € Versand)

Zum Wunschzettel hinzufügen

* Ausnahmen beachten Details anzeigen

1
Erbauer Zapfenschneider und Kegelsenker-Set 4-tlg wurde bewertet mit 3.7 von 5 von 31.
Rated 5 von 5 von aus Great value Bought for drilling and plugging some oak threshold strips. Drilled a couple to check sizing which was good so drilled 20 plugs one after the other in oak. Nothing dulled, nothing changed from first to last. Drill, cut plug, tap in with mallet using a bit of wood glue, done. As a side note, the plugs are better quality when drilled with a pillar drill, using a cordless allows for the core cutter to wonder slightly on the way in to the timber but not detrimental if your careful. Definitely recommend. Would buy again.
Veröffentlichungsdatum: 2017-11-09
Rated 4 von 5 von aus Mixed results? I'd only been using the larger set, until today, and getting very good results. The plugs were smooth and tight. However, this morning I used the smaller set and the plug cutter was chattering, even in the pillar drill, and the plugs were rough and undersize. Inspecting the small cutter I found a burr on the inside from where the cutting edge had been ground. I removed this with a needle file (could have used a rolled tube of emery paper) and tried again. This time the small plugs were also smooth and tight. This may well explain the very mixed results reported by some users. Another quick tip: If you want to sink an existing screw then remove the pilot drill from the countersink and reverse it, so the tail of the drill acts as a guide and doesn't chew the screw hole. If it's a bit loose then wind tape around until it's a snug fit in the hole. Great for hiding screws on garden furniture etc.
Veröffentlichungsdatum: 2016-04-21
Rated 5 von 5 von aus Great bit of kit Very pleased with this product. Cheaper than others but nice clean, fast cut and plug fits snugly.its already cut hundreds of hardwood plugs and still seems sharp as new.not normally a fan of this brand but these are doing a great job.
Veröffentlichungsdatum: 2016-10-01
Rated 5 von 5 von aus Value for money I brought these as I have lost my last set. I have only used them once but was very pleased with the ease in which they cut through the plugs. The countersink bit also cut through with ease I did have to put a dab of glue on the plugs to ensure they stayed put Overall very happy and at this price and the use I will give them ( occasional) they will last until I loose them again Highly recommended
Veröffentlichungsdatum: 2016-07-22
Rated 5 von 5 von aus Great tool I think the last reviewer was using this tool at too high an rpm. I've been using this for years whilst building a yacht and it's still going strong
Veröffentlichungsdatum: 2014-12-02
Rated 4 von 5 von aus Great product Getting perfect cuts everytime, plug fits very snug in counter sink. Not sure why I use to pay more then double for the trend ones.
Veröffentlichungsdatum: 2015-10-24
Rated 4 von 5 von aus Good * even for a novice Read all the reviews - good and bad - and decided to go for it. Many thanks indeed to reviewer warpc0il , who warned about burrs inside the plug cutters - found some on mine and cleaned them off with a bit of alumnium oxide paper. Really easy to use! I was machining oak and was a bit worried about the plug cutter bit as I don't have a pillar drill. In the end it was really easy to produce excellent, tight fitting results by hand. I really don't understand the reviewers who have reported broken bits, poor cutting etc., These aren't intended for rapid cutting and work just fine if you don't rush them,
Veröffentlichungsdatum: 2017-09-14
Rated 1 von 5 von aus Plug Cutter Bought this to do a skirting job, managed to do 3 holes and it was burnt out. Absolute piece of junk, not fit for purpose.
Veröffentlichungsdatum: 2014-03-27
  • y_2019, m_3, d_24, h_23
  • bvseo_bulk, prod_bvrr, vn_bulk_2.0.11
  • cp_1, bvpage1
  • co_hasreviews, tv_0, tr_31
  • loc_de_DE, sid_3375T, prod, sort_[SortEntry(order=RELEVANCE, direction=DESCENDING)]
  • clientName_screw-fix-de