Informationen zu Lieferzeiten – hier ansehen

Erbauer Diamant Lochsägekranz 152 x 150 mm Artikelnummer: 8257K

34,89 €
Exzellente und schnelle Schnitte in allen Arten von Beton und Gemäuern.
Technische Daten
Zusätzliche Information
Erbauer Diamant Lochsägekranz 152 x 150 mm

Special Price 34,89 €

Statt 69,99 €

Inkl. 19% MwSt. versandkostenfrei

Sie sparen 35,10 € (50%)


Markt wählen

Zum Wunschzettel hinzufügen

* Ausnahmen beachten Details anzeigen

Erbauer Diamant Lochsägekranz 152 x 150 mm wurde bewertet mit 4.4 von 5 von 12.
Rated 4 von 5 von aus If you need a hole.. This does as it should, took about 4 mins to cut through a brick cavity wall, I would say it's quite expensive for what it is, material cost must be a small percentage of the price paid However if you need a hole for soil pipe and want to get the collar on the bend in the hole then this is the size you need
Veröffentlichungsdatum: 2016-09-13
Rated 5 von 5 von aus Ronnie Core Bit This core bit or Ronnie as they're sometimes affectionately known did a cracking job to cut through a Victorian stone house for an extractor fan. It breezed through the internal block work and even when faced with a very brittle stone wall (which kept chipping in large chunks) it eventually cut into the stone and made it through. Presume it would easily cut through most masonary to be honest
Veröffentlichungsdatum: 2017-07-31
Rated 5 von 5 von aus Great bit of kit for the price Need to put two 150mm vents through concrete block. Having used smaller core drills in the same range went for this one. Some trepidation given size, and over whether my sds drill was man enough. Reality was that it was easier going than some of the smaller cores. Two full cavity vents with no obvious wear to segments. A+
Veröffentlichungsdatum: 2019-02-02
Rated 5 von 5 von aus Value for money Bought to cut a few cooker hood vents, took it's time getting through the external house brick but no bother and went through internal block like butter. Solid construction and good value for the money compared to what you could pay. Could probably do with a little grease on the threads after use.
Veröffentlichungsdatum: 2015-08-03
Rated 4 von 5 von aus Effective 152mm core bit I've used smaller Erbauer core bits in the past and they have been fine. After reading the reviews for this larger dia' I was worried that it may not be up to the task of drilling two holes in the side of an old manhole (engineering bricks). It started off fine (using a large 1000w sds) but definitely slowed right down when reaching the ultra hard heart of the bricks - but we persisted and succeeded. Two of us taking turns on the drill took approx half a day - not too bad for engineering bricks.
Veröffentlichungsdatum: 2018-07-16
Rated 5 von 5 von aus Good drill Outstanding cutting performance and excellent value for money! Would recommend to any tradesman!
Veröffentlichungsdatum: 2015-03-20
Rated 1 von 5 von aus Diamonds are forever?! Did I end-up with a 'duffer'? I purchased this to drill through a 110 year old solid 9" red common brick wall (to install a kitchen fan). I used my SDS until the core jammed at about 50mm of cut depth - the clutch on my SDS didn't operate and I was whacked - HARD - as the SDS spun, OUCH! Seems my SDS drill clutch had failed - the moral is do not use large diameter core drills with a powerful but clutchless drill. So a new SDS from Screwfix - a Titan and excellent this drill was. However the Erbauer core bit turned out to be rubbish... given that it took almost 5 hours 'solid' effort to get through the wall using the Titan at full revs - but without the hammer use, which shouldn't be required with any diamond cutting implement. I now need to cut a 125mm hole on the same wall for a boiler flu. I'll go for the Erbauer 127mm x 150mm diamond core drill bit - as a bit of an experiment really. Here's hoping my previous experience was atypical - I'll be leaving a review on the 127mm regardless.
Veröffentlichungsdatum: 2016-05-26
Rated 4 von 5 von aus Electrician Review Good, solid piece of kit. Did exactly what it should. Nice sharp edged hole. But, my, was it slow work. Mind you, this was the first 152mm dia hole I've cut and maybe they do take a long time compared to smaller diameters.
Veröffentlichungsdatum: 2017-11-17
  • y_2019, m_6, d_25, h_7
  • bvseo_bulk, prod_bvrr, vn_bulk_2.0.12
  • cp_1, bvpage1
  • co_hasreviews, tv_0, tr_12
  • loc_de_DE, sid_8257K, prod, sort_[SortEntry(order=RELEVANCE, direction=DESCENDING)]
  • clientName_screw-fix-de