• Lieferbedingungen
  • Widerruf
  • Zahlarten
  • Trusted Shops
  • Top Shops

Erbauer Diamant Lochsägekranz 28 mm x 300 mm Artikelnummer: 2150K

19,99 €
Exzellente und schnelle Schnitte in allen Arten von Beton und Gemäuern.
-
Technische Daten
-
Zusätzliche Information
Lieferumfang
Erbauer Diamant Lochsägekranz 28 mm x 300 mm
19,99 € Inkl. 19% MwSt., (zzgl. 4,95 € Versand)

oder

Markt wählen


Zum Wunschzettel hinzufügen

* Ausnahmen beachten Details anzeigen

1
Erbauer Diamant Lochsägekranz 28 mm x 300 mm wurde bewertet mit 3.3 von 5 von 9.
Rated 5 von 5 von aus Excellent tool for the job While this is only available in 300mm length, it helped when reaching over kitchen wall cabinets! No pilot drill, so made up a 12mm plywood template with a 300mm dia. hole to help start it off. Yes, this takes some doing when holding the drill with one hand. I used a drill without a clutch, which was a little risky. By holding it very carefully I managed to drill 6 holes through 4" concrete blocks, some at skirting level and some above wall units. Take care and it will perform fine. If the core of the bored material breaks off, it is worth removing the bit and shaking/driving it out. This will allow for easier removal of the dust. Remember not to use hammer action.
Veröffentlichungsdatum: 2015-12-03
Rated 1 von 5 von aus worst drill bit ever this bit wore out after cutting 2 inches of concrete. I used this bit AND a larger bit (DIFFERENT BRAND) to cut into the same material using the same drill so i am comparing like for like. My old bit is still good for another five years this one is going back to screwfix.... I am dissapointed because erbauer are usually a reliable brand for blades
Veröffentlichungsdatum: 2012-07-09
Rated 2 von 5 von aus Had to buy two as first broke! Needed to finish a job and only drill of size I could get at the time 'off the shelf'. Bought to drill core for 500mm lenght in brick and breeze wall. Drilling took some time, so slow cut rate. half way through the second hole the I lost all the teeth off drill. As I had started had to get another one. Not best pleased with quality and durability. Probably overheated drill as such a long core. It could therefore be ok for short core drilling. I have found this make of core drill to take for ever to drill core in past so not the sharpest drill in the box!
Veröffentlichungsdatum: 2011-10-23
Rated 5 von 5 von aus Diamond core drill I found the product easy to use - it did the job that I required quickly and neatly - it is definitely worth getting the best tool for the job as the alternative would have been a cold chisel and hammer which would not have given me such a neat finish.
Veröffentlichungsdatum: 2012-03-26
Rated 5 von 5 von aus as good as the expensive makes we have granite, engineering bricks and other hard materials in wales this does the job.
Veröffentlichungsdatum: 2015-05-31
Rated 3 von 5 von aus Could do better Overall, this is not a terrible product, especially at the price. However, it would be much more useful if this came as a kit (ie including a long enough masonry bit to provide a pilot hole). The core works OK, although wear was quickly evident, but I spent longer trying to fit the pilot drill bit to my core holder than I did actually drilling.
Veröffentlichungsdatum: 2015-03-04
Rated 1 von 5 von aus broke in 30 seconds Maybe this was defective but one of the lugs broke off within 30 seconds. I had a job on so had to drill lots of much larger holes with an old cheapo core drill without issues. I've had success with lots of Erbauer stuff but this is very poor.
Veröffentlichungsdatum: 2016-11-28
Rated 5 von 5 von aus Erbauer Diamond Core Drill Bit Excellent This core drill does the job. i was expecting it to burn out as i had to drill a concrete lintel no issues at all, even cut through re bar, good value for money i would purchase again
Veröffentlichungsdatum: 2015-05-14
  • y_2017, m_9, d_16, h_2
  • bvseo_bulk, prod_bvrr, vn_bulk_2.0.3
  • cp_1, bvpage1
  • co_hasreviews, tv_0, tr_9
  • loc_de_DE, sid_2150K, prod, sort_[SortEntry(order=RELEVANCE, direction=DESCENDING)]
  • clientName_screw-fix-de